Save on Pinterest

Framing Basement Walls

A poor framing job can bring a whole mess of problems, so we asked a professional framing carpenter how to best build basement walls. These were their expert tips for framing basement walls.

1 / 16
Framing an unfinished basement | Construction Pro Tips
Family Handyman

Framing basement walls

Framing basement walls seems pretty straightforward, slap up some studs and caller er a day. But a poor framing job is a real headache for the drywall guys, trim carpenters and every other sub who works on the project. And inadequately prepped basement walls could ultimately lead to moisture and mold problems. We asked a professional framing carpenter how to build basement walls that are dry, straight, plumb, and strong. (Note: We only address building perimeter walls in this story)

2 / 16
Putting Sealant on the Walls | Construction Pro Tips
Family Handyman

Seal the wall

Start by rolling on a masonry waterproofing product. This step is only to help prevent water that naturally migrates through concrete through a capillary effect. Roll-on waterproofing is in no way a permanent solution to a bulk water infiltration problem. If the walls are damp from condensation, dry them out with a humidifier before using the product. One choice is DRYLOK, which is available for $25 a gallon at home centers and hardware stores.

3 / 16
Instal foam board | Construction Pro Tips
Family Handyman

Install foam board

After your waterproofing has dried, install 2-in. extruded polystyrene (XPS) foam board insulation. Be sure you use XPSother types are not as moisture resistant. Stick it to the wall with a construction adhesive thats specifically designed for foamregular construction adhesives will melt the foam.

Apply the adhesive in vertical strips in the middle of the wall. If some water does get behind the foam, adhesive applied horizontally could cause the water to pool up and lengthen the time it takes to dry up. Run a continuous bead of adhesive at the top and bottom of the wall, and tape all the seams. This will help keep warm air in the room from getting behind the foam and condensing on the cool concrete walls. To ensure a good seal, Phil prefers to caulk the bottom after the foam is installed.

4 / 16
Install blocking between joists | Construction Pro Tips
Family Handyman

Install blocking between joists

When the floor joists run parallel to the wall youre building, youll need to install blocking for attaching the top wall plate. Screw or nail one side of the block through the joist, and secure the other side to the sill plate. Use treated lumber if the brace will come in direct contact with bare concrete. It may be easier to install the braces before you install the foam board on the walls and insulate your rim joist. Phil places his blocks 2 ft. apart so they work as drywall backers too.

5 / 16
Snap lines on the floor | Construction Pro Tips
Family Handyman

Snap lines on the floor

Snap a line on the floor 4 in. away from the foam as a guide for the bottom plate. This will leave a 1/2-in. gap between the bottom of the new wall and the foam. Thatll allow a bit of wiggle room if the foundation walls arent perfectly plumb or straight.

6 / 16
Assemble walls on the floor | Construction Pro Tips
Family Handyman

Assemble the wall on the ground

If you have the space, its faster and easier to assemble a wall on the ground. Sight every stud for a crown (a slight curve on the narrow side of the board), and mark an X on the crown. Have all the crowns face the same direction. If you dont, youll end up with a wavy wall.

Its easier to assemble your wall with the crowns up; that way both ends of the studs are solidly on the ground when you attach the top and bottom plates, instead of acting like rockers on a rocking chair. Build the wall so it can be tipped right up; theres usually not enough room to swing the whole wall around if you dont.

7 / 16
Tip the walls into place | Construction Pro Tips
Family Handyman

Tip up the walls

Its usually easier to tip a wall up with the bottom plate against the wall, but if the floor joists are sagging or theres ductwork in the way, you may have to lift the top of the wall in first and slide the bottom plate into place as shown above. If youre working alone, dont build a wall too heavy to lift. Save your back by building smaller sections and tying them together after you set them in place.

8 / 16
Build the walls short | Construction Pro Tips
Family Handyman

Build the walls short

If you need to pound the walls into place with a sledgehammer, youve built your walls too tall. Theres no reason that the top plate has to be tight against the joiststhats what shims are for. Measure the distance from the floor to the joists at several locations and build your wall at least 1/4 in. shorter than the shortest measurement. Trying to force a wall into place can raise the joists, which could wreak havoc with drywall joints and flooring on the rooms above.

9 / 16
Fasten the bottom plate | Construction Pro Tips
Family Handyman

Fasten the bottom plate

This pro fastens his walls to the floor with construction adhesive and a powder-actuated tool (PAT). He spaces fasteners every 6 ft. and within 6 in. of each end.Wear safety glasses and hearing protection because these suckers are usually very loud. Phil usually shouts out Fire in the hole to warn other people in the area. Tapcon screws work great as well.

10 / 16
Plumb and secure the top plate | Construction Pro Tips
Family Handyman

Plumb and secure the top plate

Instead of snapping a line for the top plate, Phil plumbs the wall about every 4 ft. using an adjustable level that reaches from the bottom plate up to the top. If you dont own a $300 plate level, use at least a 4-ft. level, and try to find the straightest studs to use as a guide. You need shims only about every third joist, but nail the top plate to every joist. Its not necessary to align the studs directly under floor joists, but its a good idea if you plan to run ductwork or plumbing in the walls.

11 / 16
Build in place when neccessary | Construction Pro Tips
Family Handyman

Build in place when necessary

If your floor is horribly out of level, or if youre framing around a window, it may be best to stick frame, nailing one stud at a time instead of building the wall on the floor. Start by fastening your bottom plate, and then use a straight stud and a level to plumb up to find the location for your top plate. After you snap a line and fasten your top plate, plumb up again and mark the location of your first stud on both plates. Mark the rest of the stud locations on the plates using those marks. Toenail each stud into place with two nails on one side of the stud and one on the other.

12 / 16
Inside Corners | Construction Pro Tips
Family Handyman

Inside corners

When he frames inside corners, Turn the last board on the first wall sideways and overlaps it about halfway past the connecting wall. This way he can fasten the two walls together and still have a surface for attaching the drywall.

13 / 16
Build out around windows
Family Handyman

Build out around windows

Windows set in a block or concrete wall will need wood around them in order to attach the drywall or jamb extensions. If theres room, use foam under the boards, and tape the seams to the foam youve installed on the wall. If theres no room for foam, make sure to use treated lumber, but still tape the seams. Construction adhesive and concrete screws work best to attach these boards. Install the wood around the window before you build your wall. That way youll know exactly where the new wall framing needs to be.

14 / 16
Don't forget drywall backers | Construction Pro Tips
Family Handyman

Dont forget drywall backers

Its a lot easier to add drywall backers while you still have all your framing tools out and before you fill the wall cavities. So before you pack it up, walk around the entire work area and make sure the ceiling and all walls have a sufficient nailing surface for the drywall. The top of outside corners, perpendicular intersections, and walls that run parallel to the joists are three of the most common areas where youll need to add backers.

15 / 16
Meet the expert framer | Construction Pro Tips
Family Handyman

Meet the expert

Phil Geis has been a framing carpenter for more than 20 years. He started out helping his uncle on remodeling projects while he was still in high school. He and his crew have built more than 300 new houses and breathed new life into dozens of old basements.

16 / 16
Family Handyman

We’d Love to Hear From You


Do you have a jobsite or tool tip that makes your work-life easier, safer, or just more fun?Why not share it with your construction comrades? Plus, you can show off your professional prowess to your family and friends.

Click the image below to send us your Pro Tips! Please include an image if you can. We will contact you if we run your submission on the site.