Guide To Exterior Spray Painting
Airless paint sprayers are by far the most efficient way to paint. Learn more about how to use and the best techniques here.
Painting with an airless paint sprayer
Every professional painter owns an airless paint sprayer. Theres just no more efficient way to deliver paint onto a surface, and for most pros, every minute saved is money in the bank. And the smooth, even finish that sprayers deliver just cant be matched with a brush or roller.
Working with a paint sprayer may seem intimidating, but it only takes a few minutes to get the hang of the proper technique. We visited the training/testing facility at Schoenfelder Renovations in Hopkins, MN, where Daryl Becker showed us the basics. He also shared some extra gems you wont read about in the operators manual for your paint sprayer. In this story, well focus on exterior painting, but most of these tips apply to any painting job that involves a sprayer.
Whats an airless sprayer?
Airless sprayers work by pumping paint at very high pressures (up to 3,000 psi). They can suck paint from a large bucket (fewer refills), and the gun is lighter because its not attached to the paint reservoir, as is the case with many air sprayers. Airless sprayers can spray both paint and finishes. There are different tips for different materials.
An entry-level model will cost about $250. The Graco X7 model shown retails for $370 at home centers. Pros use models that range from $500 up to several thousand dollars. The basic operations of the machines are the same; what you get for your extra dollars is mostly durability. You can rent an airless sprayer for about $85 a day.
Adjust the sprayer, starting with low pressure
The thickness of the paint will determine the proper pressure setting on the sprayer. Start with the pressure on low and make a pass on a scrap piece of cardboard or rosin paper. If the pressure is too low, the spray pattern will be uneven and therell be fingers on the edges. Keep upping the pressure until you get a nice, even spray pattern with a consistent edge. If the pressure is all the way up and the pattern is still weak, you may have to go up one tip size.
Keep the gun perpendicular to the wall
To achieve a consistent layer of paint, the tip of the sprayer should be held about 12 in. from the surface and the gun should always remain perpendicular to the wall. This technique is the foundation for a professional finish. It seems tricky at first, but after only a few passes youll be painting like a pro. Practice on a low-visibility wall until you get the hang of it.
Tape off windows and doors
Before you crack open that first bucket of paint, tape off your windows and doors. We prefer the dispensers that roll out the tape and plastic at the same time. You can buy a high-end dispenser like the 3M M3000K shown for about $70 at paint stores. More basic models can be purchased at home centers for $20. Only the face of the trim needs to be protected (more on that later).
Keep a lid on it
Always keep the lid on the bucket. Just remove the small cap and stick the intake tube into the smaller hole. This will keep debris out of the paint and prevent clogs. Plus, an open bucket dries out faster, and dried clumps of paint can also clog the works. Always use a 5-gallon bucket. If your project only requires 3 gallons, pour that amount into an empty 5-gallon bucket and draw your paint from that.
Overlap 50 percent and keep the gun moving
Overlap the pattern about 50 percent. Release the trigger at the end of each pass. Start the gun in motion before pulling the trigger. If you start spraying with a stationary gun, youll get a glob of paint. When spraying under lap siding or the side of trim boards, angle the tip upward so you get enough paint on the bottom portion of the board. Always start at the top of the wall and work your way down.
Back-roll, then recoat
After you back-brush, its time to back-roll. Dont spray an area so large that the paint dries before you can roll it out (drying times vary greatly depending on the weather). A roller with a thicker nap is better at reaching the uneven surfaces. Many pros use a roller with a 3/4-in. nap because it gets up into more of the recessed areas. And while its tempting to roll lap siding horizontally, always roll in an up-and-down motion. Its hard to stop the paint from dripping off the bottom of the laps if you roll horizontally.
One coat may be enough if youre just freshening up the paint with a new coat of the same color. But if youre working with new siding or changing colors, a second coat will be needed. But no back-brushing or back-rolling is necessary on the final coat, so it goes fast, and the final coat hides many of the smaller brush and roller marks.
Back-brush the nooks and crannies
If you thought you could just blast the wall with a sprayer and call it a day, Ive got bad news for you. The paint sprayer is only a paint delivery system. In order to achieve a coating that will last for years, you need to push the paint into every crack and crevice and underneath every lap with a brush. It seems like a tedious extra step, but its absolutely necessary.