Save on Pinterest

7 Odd Tools That are Invaluable for Some Trades

Can you guess what these unique tools are used for?

Every editorial product is independently selected, though we may be compensated or receive an affiliate commission if you buy something through our links. Ratings and prices are accurate and items are in stock as of time of publication.

1 / 7
A portable generator that runs off of propane | Construction Pro Tips
Courtesy of Generac

Propane Is Easier Than Gas

When it comes to portable generators and ease of use, liquid propane (LP) definitely beats gasoline. Gasoline is a handy fuel, but it’s not without problems. Storing enough gasoline to get you through a several-day power outage requires constant vigilance. You have to buy several 5-gallon gas containers, fill them up, add fuel stabilizers and find a safe place to store them. Gasoline also needs to be replaced after several months to make sure it’s still fresh when you need it. Propane makes the whole operation much more straightforward and requires much less maintenance.

Shop Now

2 / 7
Repairing shingles with a specialty tool | Construction Pro Tips
Courtesy Roof Snake

Shingle Repairs Made Easier

Replacing damaged shingles is tough on super-hot days—the shingles are soft and tear apart. It’s not much easier on cold days—frozen shingles break in two if you pry them up too far. But the “Goldilocks approach,” waiting for the temperature to be just right, isn’t always an option.

The Roof Snake by PacTool International makes shingle repairs easier. Here’s how it works:

  • Pry up a little bit on the surrounding shingles to remove the nails that hold down the damaged one.
  • Pull out the old shingle and slide a new one into place.
  • Flip the tool around and insert a roofing nail into the nail slot.
  • Slip the tool under the overlapping shingle, and (here’s the ingenious part) hit the tool with your hammer to get the nail started.
  • Then pull the slot free and pound the nail in with the flat part. Because you don’t have to pound directly on the nail, the shingles don’t need to be pried up so far, making damage less likely.

Shop Now

3 / 7
Wire brush from SPYDER Tools | Construction Pro Tips
Courtesy SPYDER Tools

Wire Brush for Your Reciprocating Saw

Reciprocating saw accessories have come a long way, and the folks at Spyder Tools have a lot to do with that. The newest kid on the block is a wire brush. Stick it in the end of your reciprocating saw and scrub away dirt, rust, and unwanted paint. You shouldn’t throw away the wire wheel for your grinder, but this setup is easier to control than a grinder, and because it’s portable and small, it can reach areas grinders can’t. There’s nothing better than finding a new use for an existing tool. You can get the Spyder Tools wire brush at home centers, hardware stores, and online.

Shop Now

4 / 7
Man cutting insulation with a shut-n-cut | Construction Pro Tips
Courtesy Shut n Cut

Simple Insulation Cutter

If you hang insulation more than a couple of times a year, the Shut-N-Cut is more than worthy of consideration—it’s a no-brainer. Here’s how it works:

  • Attach the Shut-N-Cut to a table or sawhorse
  • Lay a batt over it
  • Clamp the batt in place
  • Slide the insulation knife through the slotted clamping arm and get to hanging.

No more kneeling on the ground or changing blades every 15 minutes, and no more pulling half-cut batts apart with your hands, throwing tons of nasty fibers into the air.

Shop Now

5 / 7
Scraping tool attached to an oscillating tool | Construction Pro Tips
Courtesy Spyder Tools

Did You Know You Owned a Power Scraper?

Another great reciprocating saw accessory from Spyder is the Spyder Scraper blade, which transforms your reciprocating saw into a power scraper. These blades aren’t tough enough for concrete or tile demo, but they do a nice job of removing vinyl flooring or glue-down carpeting. One warning, though: A sharp Spyder Scraper blade will chew right through a wood subfloor. The trick is to keep the saw at a low angle and let the tool do the work—don’t push too hard.

The 2 and 4-inch blades are the most useful. The 6-inch blade causes more kickback, which will eventually destroy either the blade or your wrists. Spyder Scraper blades are not the tool to reach for if you need to remove tiles from an entire gymnasium floor, but these blades deserve a spot in your reciprocating saw’s box for smaller jobs.

Shop Now

6 / 7
A flexible Tweel from John Deere | Construction Pro Tips
Courtesy John Deere

Not a Tire, Not a Wheel…it’s a Tweel

Pro landscapers are going to love this. John Deere ZTrak 900 commercial mowers can now be outfitted with Michelin X Tweel Turf tires that won’t ever go flat and ride much smoother than pneumatic tires. The benefits are almost too obvious to mention: no more downtime repairing flat tires and much less bouncing around, which is a big-time back saver.

Upgrade to the X Tweels is expensive, but one set will last as long as three sets of pneumatics (not to mention all the money you’ll save on chiropractic visits). Right now X Tweels available only for commercial mowers, but this technology will be rapidly expanding.

Check out a video on the Tweel and more product information here on John Deere’s website.

Shop Now

7 / 7
Light held up by a gear tie | Construction Pro Tips

Gear Stand

Flexible gear ties work great for securing tools for travel, but they come in handy for all sorts of other stuff, like holding a flashlight in place while you work. The one pictured is made by Nite Ize and is available online as well as in many hardware stores and home centers.

Shop Now