Most dryer problems can be fixed in an hour with a few basic tools and a continuity tester or multimeter—and you can do the work yourself with these simple instructions.
By the DIY experts of The Family Handyman Magazine
You might also like: TBD
If your dryer breaks down
Here’s the first thing to know about dryer repair: You can solve most dryer troubles yourself. There’s no need to find a technician, schedule a service call or pay hundreds dollars for dryer repair.
The dryer repair fixes we show in this article correct about 90 percent of dryer breakdowns. Most repairs take about an hour, but set aside extra time to locate replacement parts. To find parts, search online for “appliance parts.” Most parts are relatively inexpensive. Aside from basic tools like a socket set and screwdrivers, you may need a continuity tester or multimeter to diagnose the problem.
Tip: The first step in any appliance repair is to make sure it’s getting electricity. Unplugged cords and tripped breakers are a leading cause of appliance “breakdowns.”
Most dryer repairs require some disassembly of the outer cabinet so you can get at the parts inside and you might not even need a dryer repairman. If your dryer’s lint filter is inside the front door (Figure A), disassemble it this way: First, remove the screws at each corner of the control panel. Flip the panel up and back to expose the screws in the top panel. Remove the screws, then pull the top toward you and lift it off. To open the bottom panel, release the spring catches by shoving a putty knife into the slot just above them. With the bottom panel open, you can remove the front panel by removing two screws at the top and two at the bottom.
If your filter slides into the top of the dryer, remove the screws alongside the filter slot. Using a putty knife, release the two spring catches located under the top panel at the front. Tilt the top panel up like a car hood and remove the screws that hold the front panel in place.
Figure A: Disassembling a Dryer
Dryer disassembly is slightly different depending on where the lint filter is located, but either way most repairs to gas dryers require that you remove the top and front (not the back or sides) to access the parts.
Don’t get shocked! Unplug the dryer before you do any disassembly, diagnostic or dryer repairman work. On a gas dryer, also turn off the gas supply shutoff valve.
Dyer Repair: How to Fix a Dryer that Won’t Start
Door switches can wear out, causing the dryer to stop working.
Test the switch
Pull the wires off the door switch. Open and close the door while testing for continuity. If you don’t get continuity, replace the switch.
If your dryer seems absolutely dead when you turn it on, chances are the door switch is bad or the plunger is broken or bent. Door switches wear out from normal use, but repeatedly slamming the door can speed up their demise. Start by checking the plunger located on the door for dryer troubleshooting. If it’s missing or bent, replace it. If the plunger checks out, the next step of dryer troubleshooting is to remove the top cabinet panel to gain access to the door switch. See the disassembly instructions.
Test the switch for continuity. If the switch is good, test the thermal fuse (see “No heat” below) mounted on the blower housing. If you have a gas dryer with the lint filter in the door, access the thermal fuse by opening the bottom panel. If the filter slides into the top of the machine, remove the entire front panel. On an electric dryer, remove the rear service panel. If you don’t get a continuity reading from the thermal fuse, do NOT simply replace it. A blown thermal fuse is a warning that you have other serious problems—either a malfunctioning thermostat or a clogged vent. Fix those before replacing the fuse.
Dryer Repair: Dryer thumps, rumbles or chirps
Replace drum support rollers
Clip off the old triangular roller keeper and remove the roller. Wipe the shaft with a rag and alcohol and install the new roller and keeper. Do NOT lubricate the shaft.
The drum support rollers are worn. Replace all of them. If the noise continues, replace the tensioner roller (see below). Since it takes longer to disassemble the machine than to actually replace the rollers and belts, we recommend replacing both of them at the same time.
Using a Continuity Tester
Our photos show using a multimeter to diagnose trouble. But a continuity tester, which is much cheaper, will also work for all the troubleshooting in this article. To use a continuity tester, simply attach the clamp to one contact point and touch the probe to the other. If the light glows, you’ve got continuity. If not, you’ve got trouble.
Dryer Repair: No heat
The heat won’t come on if any of these parts are broken.
Photo 1: Check continuity
On a gas dryer, test the radiant sensor, igniter and thermal fuse by disconnecting the wires and checking for continuity. Replace them if they fail the continuity test.
Photo 2: Check the heating element
Disconnect the wires to the heating element of an electric dryer and test it for continuity. Replace the element if you don’t get a continuity reading.
Photo 3: Replacing the heating element
Replace the bad heating element on an electric dryer by unscrewing the retaining clip at the top of the heater box. Then pull out the box and remove the element retaining screw. Swap the elements and reinstall.
If you have an electric or gas dryer that tumbles but won’t heat, check the thermal fuse for continuity. If the thermal fuse checks out, move on to the radiant sensor if you have a gas dryer. It monitors the igniter and powers up the gas valve coils when the igniter reaches peak temperature. A bum sensor will stop the whole show. Test it for continuity (Photo 1) and replace it if it fails. If the sensor is good, disconnect the electrical connector to the igniter and check it for continuity. Again, replace it if it fails the continuity test. If both the radiant sensor and the igniter pass the test, replace the gas valve coils. To replace them, remove the retaining plate, unplug the sensors and pull them off the gas valve.
If the thermal fuse on your electric dryer checks out, test the heater element for continuity. Replace the element if you don’t get continuity (Photos 2 and 3).
Dryer Repair: Drum won’t rotate, but the motor runs
Replace the belt
Route the new belt around the drum and toward the motor/tensioner assembly. Reach your hands around the motor and retract the tensioner so you can wrap the belt around the motor pulley.
Don’t know how to fix a dryer belt? You’re in luck—it’s only a broken belt. Remove the front cabinet panel and lift the entire drum out of the cabinet. Now’s the time to fire up your shop vacuum and suck out all the lint. Then spin the tensioner roller by hand to see if it runs smoothly and examine it for cracks. Replace the tensioner if it fails either test. Reinstall the drum and wrap the new belt around it (ribs facing the drum). Some tensioners are mounted behind the motor, so they’re difficult to see from the front access panel. You’ll have to do this by feel. Reach your hands around the blower housing and lift the tensioner up while you route the belt around the motor pulley. Voila, you are now a dryer repairman.
Quick Fix for a Dryer Door
If your dryer door won’t stay closed, chances are the latch is either bent or missing, or the strike is worn. The fix is cheap and easy. Buy the parts from any appliance parts store. Then grab pliers, a couple of small, straight-slot screwdrivers and a roll of masking tape.
Grab the bent or broken latch and yank it out. Then install the new one, pushing in firmly until the locking tabs seat (Photo 1). Next, protect the door’s finish with tape and remove the old strike. Jam a small screwdriver into the strike and bend the metal locking tab inward. Pry upward with a second screwdriver to pop it out (Photo 2). Snap in the new strike and you’re back in the laundry business.
Required Tools for this Dryer Repair Project
Have the necessary tools for this DIY project lined up before you start—you’ll save time and frustration.
You’ll also need either a multimeter or a continuity tester and a small straight slot screwdriver.
Required Materials for this Dryer Repair Project
Avoid last-minute shopping trips by having all your materials ready ahead of time. Here’s a list.