How to DIY a Ceiling Garage Storage System
Build this simple, slide-in storage system for your garage.
A full day
IntroductionIf your garage is running out of space, try building this overhead storage system. The construction is simple and fast, and the whole system is made with standard materials.
- Circular saw
- Cordless drill
- Drill bit set
- Miter saw
- Safety glasses
- Socket/ratchet set
- Stud finder
- 1/2 1x2 x 8' pine stop strip (1)
- 1/4" x
- 2" wood screws (1 box)
- 23-1/2" x 19-1/2" x 13" plastic totes (6)
- 2x4 x 8" (2)
- 3-1/2" lag screws and washers (16)
- 3" wood screws (1 box)
- 4' x 8' sheet of 3/4" plywood
- Carpenter’s glue (1 pint)
Are all those cardboard boxes in the corner of your garage driving you crazy? Holiday decorations, camping gear, seasonal clothing and extra bedding take up valuable garage storage space. And who can tell one brown box from another?We’ve designed this system to get all that stuff up and out of the way and into unclaimed storage space near your garage ceiling. We built this handy overhead garage storage system around special reinforced plastic totes that hang from carriages made from 2x4s and plywood strips. In this article, we’ll show you how to assemble these simple carriages, align them perpendicular to the ceiling joists, then anchor them into place with lag screws. It’s that easy. Add labels to the sides of the totes and you can tell at a glance where to find that long-term storage item. You can build and install the carriages in an afternoon and start organizing right away!
Project step-by-step (12)
Measure the top of the tote to determine the width of the tote rims (3/4 in.) and the size of the bottom flanges of the carriages (in our case, 3 in.).
Cut 3-in.-wide strips of 3/4-in. plywood for the bottom flange. Center them on 4-ft.-long 2x4s, then glue and screw them. Use 2-in. screws every 10 in.
Complete the Overhead Garage Storage Carriages
Flip the carriage assemblies over. Center the 5-in.- wide plywood top flanges and glue and screw them to complete the carriage assemblies.
Screw Ceiling Garage Storage System in Place
Mark each carriage 12 in. from the end and align the mark with the joist location. Screw the carriage temporarily to each joist on one side of the flange with 3-in. screws.
Mark the carriage locations
Cut a 2x4 template from your tote dimensions and mark the location of the top edge of the next carriage. Mark the rear side as well, then screw it and the other carriages in place on one side only.
Test the Fit of Your Overhead Garage Storage
Check the fit of the totes and make sure the rims have maximum bearing on the lower flanges. Make any necessary adjustments.
Drive lags at joists
Drill 3/16-in. pilot holes in the top flanges. Then drive pairs of 3-1/2-in. lag screws into each joist, removing the temporary screws as you go. Use a minimum of four lag screws per carriage.
Mark the centers of the carriages and screw a 1x2 stop along the marks. The stop will keep the totes from sliding too far into the overhead garage storage system.
The special reinforced totes we used (available from internet suppliers like usplastic.com, simplastics.com and others) are a bit stronger than those you'll find at home centers or department stores. The reinforced rims on these containers will support weights of 35 lbs. or more, which is perfect for lightweight overhead garage storage.
And the totes will be easy enough to lift into place while you're standing on a ladder. To be on the safe side, the total weight of all the totes shouldn't exceed 210 lbs., so find a different place to store books and heavy hardware. Custom plastic lids are also available for dust-free storage.
If you use other types of containers, measure the rims carefully and adjust the bottom flange width to assure full support. And no matter what joist spacing you find (24 in. or 16 in.), be sure to fasten the carriages with at least four lag screws.
Before you order your totes, measure the height above your garage door and find totes that'll work. Our 13-in.-deep totes required 18 in. of clearance, including the carriages. For lower clearances, you can buy totes that are 8 and 10 in. deep but with the same top size.