Set on no-mess strips of tile adhesive mat, shimmery glass tile becomes the perfect frame for a tile framed mirror. All you need is an MDF back, wood trim, tile, mirror and grout.
By the DIY experts of The Family Handyman Magazine
You might also like: TBD
Tile Framed Mirror: Design and layout
Tile Framed Mirror Photo 1: Dry-set the tile on a flat surface
We used paper-faced glass mosaic tiles. Theyre a little harder to work with than mesh-backed glass tiles, but theyre typically cheaper and you cant see the mesh backing through the glass. Working on a slab of 3/4-in. MDF, I fit together the tile border. This meant cutting the tile sheets to fit. Remember to leave grout spaces between the sections of tile. The MDF later became the base of the mirror.
Tile Framed Mirror Photo 2: Make sure the mirror fits
Center the mirror on the tile and make sure it overlaps the tile by at least 1 in. Then mark the outer edges of the tile border so you can cut the MDF base to size. After it’s cut, prime both sides.
Tile Framed Mirror Photo 3: Label the tile sections
This was a stroke of genius and saved us a ton of trial-and-error later on when setting the tile.
Tile Framed Mirror Photo 4: Make the frame parts
We ripped the 3/4-in. oak frame parts to a width of 2-1/2 in. The top and bottom frame parts overhang the sides by 3/4 in. We rounded the edges of the frame parts with a 1/16-in. roundover bitbut this step is optional.
Tile Framed Mirror Photo 5: Finish the frame parts
Glue doesn’t stick to finished wood, so we taped the areas that would later get glue. Then we gave the frame parts a coat of stain followed by polyurethane.
Tile Framed Mirror Photo 6: Glue and nail the frame to the base
Tack each frame part to the base with two or three brads; that’s all it takes to hold them in place until the glue dries.
Vern Johnson, TFH art director extraordinaire, is a hands-on fellow whos addicted to glass tile. He was itching for a new tile project that wouldnt break the bank. So he came up with this glass tile border and frame that transforms a plain mirror into a stunning work of art. Big impactsmall price. Heres how he did it.
Set and grout the tile
Photo 7: Lay the tile mat
If you use a tile mat, make sure to peel the paper facing off the tiles slowly so the tiles don’t move around or come off.
Photo 8: Set the tile
Having the frame already in place was another brilliant idea (man, I’m good). It made setting the tile a piece of cake because the frame automatically aligns the tile.
Photo 9: Press it into place
Make sure all sections are positioned right; adjust them if needed. Then press them hard against the mat with a scrap of plywood.
Photo 10: Mask off the frame
Tape protects the frame from the grout.
Photo 11: Remove the paper
After soaking the facing with water, I finally got to peel it back and see the gorgeous tiles. I could have avoided this extra step by using mosaic tiles on a mesh backing.
Photo 12: Grout the tile
Grout the tile in the usual way using unsanded grout.
For this project, I used a tile adhesive mata mat thats sticky on both sides (sold at home centers and tile stores). You stick one side to the frame and then stick the tiles to the face. Its easy to use, you can grout it right away and theres less mess than with mastic. But mastic would definitely be cheaper and it would work fine too.
Attach the mirror
Photo 13: Apply adhesive
Cut wood strips the same height as the tile and glue them to the base. Then apply mirror adhesive. Also run mirror adhesive around the inner edge of the tilejust a thin bead so it wont squeeze out around the mirror.
Photo 14: Set the mirror
I jiggled the mirror back and forth a few times to spread the mirror adhesive and then pressed it down. I let the whole thing cure for a day before attaching the hardware.
Photo 15: Mark the outline on the wall
I measured from the edge of the frame to the center of the studs to determine where to place the two hanger straps on the mirror. That guaranteed that both straps would land on studs. But it would have been easier to use heavy-duty drywall anchors.
Photo 16: Rout recesses for the straps
This step is only for fussy folks like me. It allows the mirror to hang tight against the wall. If you don’t mind a small gap between the mirror and the wall, skip this step.
Photo 17: Attach the straps
To avoid a trip to the hardware store, I made my own aluminum hanger straps, complete with countersunk screw holes. Then I screwed them to the mirror with 1/2-in. screws. Last step: Hang this masterpiece on the wall! For that, I used two 2-in. screws.
Use special mirror adhesive (available at home centers) to bond the mirror to the MDF backer. Carefully set the mirror in place, then let the adhesive set overnight.
After the glue has dried, turn the mirror over and mark locations for two hanger straps at the top of the mirror. If possible, match these hanger locations to the studs on the wall, but if the spacing doesnt work out where you want to place the mirror, use heavy duty drywall anchors.
Rout channels for the hanger straps with a dado bit set to the depth of the hanger. Screw the straps to the MDF backer, then hang the mirror.
Required Tools for this Project
Have the necessary tools for this DIY project lined up before you startyoull save time and frustration.
Required Materials for this Project
Avoid last-minute shopping trips by having all your materials ready ahead of time. Here’s a list.