Washing machine repair: Fix 90 percent of clothes washer breakdowns with these four easy fixes, including filling and draining problems, grinding noises and a failure to spin. You'll avoid the $80 - $150 service call.
By the DIY experts of The Family Handyman Magazine
You might also like: TBD
A full day
Overview: Time, tools and savings of washer repair
Instead of searching the internet for “washer repair near me”, we’ll show you how to fix it yourself. Washing machine repair may sound complicated, but these machines are pretty simple inside. With a few basic tools and the steps we show here, you can solve most problems yourselfand save the cost of a service call ($80 to $150). We won’t cover every fix, but the repairs we show will correct about 90 percent of washer troubles, like Maytag washer repair or Kenmore washer repair.
These common washer repairs are a snap for the average do-it-yourselfer. You’ll need a socket set or nut drivers, screwdrivers and a flashlight. Repairs can take as little as an hour, but set aside a full morning to diagnose the trouble, get parts and complete the repair. To find parts, check the yellow pages under Appliance Parts or search online for appliance parts for Maytag washer troubleshooting or a washer repairman.
Figures A and B on the following pages show two common washer styles. The outer cabinet shown in Figure A (Whirlpool and some other brands) lifts off completely, giving you access to all the parts. The washer shown in Figure B (Maytag and some other brands) has removable front and back panels.
Tip: Make sure your washer has power! Unplugged cords and tripped breakers are common causes of appliance breakdowns.
For more money-saving fixes, type appliance repair in the search box above.
Figure A: Whirlpool-Type Washer
To remove the outer cabinet from this type of washer, first pull off the side trim pieces and remove the retaining screws. Flip the console up and release the spring clips with a screwdriver. Tilt the cabinet forward and lift the cabinet off.
Note: Figure A showing Whirlpool washer repair is available in pdf format in Additional Information below.
Figure B: Maytag Washer Repair
To remove the front panel on this type of washer, yank the bottom of the panel outward (you may have to first remove screws). Pull the panel down and out.
Note: Figure B of a Maytag washer repair is available in pdf format in Additional Information below.
Unplug your washer before you begin any testing or repairs.
Fix 1: Grinding noise
Remove the pump
Pop the snap retainers with a screwdriver and pull the pump off the motor shaft. Then disconnect the electrical connectors from the motor.
Replace the broken coupler
Pop the bottom retainer off the motor and prop up the motor while you pop the top retainer (it’s heavy). Pry the broken coupler pieces off the motor and transmission. Tap the new coupler into place with a wooden block.
If you own a Whirlpool direct-drive washer (the water hoses attach to the left side when viewed from the back), you’ve probably got a broken couplera common failure caused by overloading the machine. It’s an easy and inexpensive fix, about $22.
Fix 2: Draining problems
Replace the pump
Tip the machine back and support it with blocks. Remove the pump belt and the three pump retaining screws. Tilt the pump forward and lift it out of the opening.
When clothing or jewelry gets stuck in the hose to the pump or in the pump itself, the machine won’t drain and you might hear squealing or grinding or smell burning rubber. First remove the hose that goes from the tub to the pump (drain the water into a bowl) and check for stuck socks (yes, that’s where they go). Then run a coat hanger through the tube and pull out the stuck objects. Next check the pump for broken blades by shaking it. Rotate the pump shaft to make sure it spins freely. Replace the pump if you find any damage ($55 for Maytag; $44 for Whirlpool). If you see any burned or melted sections on the belts, replace them ($35 a set). Maytag belts are specially designed, so don’t substitute an ordinary V belt.
Fix 3: Slow fill or no fill
Replace the water valve
Remove the water valve bracket and mount the new valve. Transfer the electrical connectors to the Hot/Cold portions of the new valve. Then transfer the fill hose by compressing the spring clamp.
If your washing machine fills slowly or won’t fill at all, try cleaning the inlet screens on the water valve. To see how, type inlet screen in the search box above. If that doesn’t help, replace the entire water valve assembly ($35).
Fix 4: Won’t agitate or spin
Replace the lid switch
when your washer won’t spin, remove the lid switch on a Maytag-type washer by prying up the locking tab and sliding the switch forward as you try to figure out how to fix a washer that won’t spin. To install the new switch, just set it in the slot and pull it backward.
If the machine fills with water and then just sits there, suspect a broken lid switch. To test the switch, you’ll need a continuity tester (about $8) or a multimeter (about $15). If you don’t know how to use a multimeter, type multimeter in the search box above. Remove the wires connected to the switch and touch the tester’s probes to the switch’s connectors. As you open and close the lid, readings should alternate between continuity and no continuity. If not, replace the switch ($33).
To replace the switch on a Whirlpool-type washer (Figure A), just remove the two screws and screw in the new one. To get at the switch on a Maytag-type washer (Figure B), you’ll have to unscrew the access panel behind the console and replace the switch as shown here. Remember to raise the lid before you remove the old switch.
Tip: Never drop a washing machine’s lid! Slamming the lid eventually wrecks the lid switch.