How To Make DIY Wood Wall Art with Power Carving

Carve unique wall art with these awesome angle grinder attachments.

Next Project
Time

A full day

Complexity

Beginner

Cost

$50-100

Introduction

An angle grinder is a simple, affordable and endlessly versatile tool. With the right attachment, you can grind, cut or polish metal, masonry and stone. You can also quickly sand wood, cut tile and clean away rust from metal.

I recently discovered a new attachment for my grinder: power-carving wheels. With these, I can shape wood and create reliefs and contours with ease.

I had a rough slab of cherry that seemed unusable and was headed for a campfire. It was perfect for a power-carving test run. After a dusty day of carving, I ended up with a distinctive piece of DIY wood wall art.

Tools Required

  • 4-1/2-in. angle grinder
  • 4-in. and 2-in. donut carving wheels from saburrtooth.com
  • assortment of 1/8-in.-shank burrs
  • Clamps
  • Drill
  • longneck 2-in. angle grinder
  • Orbital sander
  • Rotary tool

Materials Required

  • finishing supplies
  • Live Edge Slab

Diy Wood Carving Wall Art hanging in a living roomFamily Handyman

Take safety seriously

Fh22apr 617 55 031Family Handyman

This DIY wood wall art piece was made with an angle grinder, a handheld tool that spins at 10,000 revolutions per minute (rpm) or more.

When a spinning carving wheel hits the wood, the dust and wood chips fly everywhere. A face shield is a must; I go with safety goggles and a long-sleeved shirt, too. Because my hands are so close to the wheel, I always wear gloves and keep the side handle in place. Clamp down your workpiece and make sure the chips are flying away from anything they can harm.

Project step-by-step (7)

Step 1

Draw the Contours for the DIY Wood Wall Art

To make my DIY wood wall art design (see Step 7), I began by drawing lines to indicate the highest contour — the peaks. I followed the grain but also deviated from it to create interesting crossing patterns. Sketch your lines with a pencil. Once you like the shapes, go over them with a white china pencil.

Diy Wood Carving Wall Art Fh22apr 617 55 011

Step 2

Define the Depth

To establish a consistent depth for the valleys, I drilled holes every few inches between my lines. I marked the depth with a tape flag on a 1/4-in. drill bit before drilling. You can skip this step if a consistent depth isn’t important.

Diy Wood Carving Wall Art Fh22apr 617 55 014

Step 3

Shape the Contours

With a coarse-grit carving wheel, I removed material between the lines, carving until the 1/4-in. holes disappeared. I started in the middle of the valleys and carved slopes toward the peak lines. Once I removed most of the material, I switched to a medium grit, then finished with a fine-grit carving wheel.

Diy Wood Carving Wall Art Fh22apr 617 55 016

Step 4

Two-Inch Wheel for Precision

To carve with more precision and reach areas the four-inch wheels couldn’t, I used two-inch carving wheels with this special longneck two-inch angle grinder by Proxxon.

Diy Wood Carving Wall Art Fh22apr 617 55 036

Carving Wheels Coarse Medium Grit

Step 5

Refine the Shape with Burrs

Available in similar grits and many shapes, these 1/8-in.-shank burrs allow you to shape details in smaller crevices. The burrs fit into many rotary tools and are especially easy to use in rotary tools with a flexible shaft.

Diy Wood Carving Wall Art Fh22apr 617 55 040

Fh22apr 617 55 008 Grid

Step 6

Sand it Smooth

I sanded this piece with 80-grit through 180-grit sandpaper. I used an orbital sander where it would fit, then switched to sanding sponges to follow the contours. Depending on the look you’re after, sanding could be the slowest, most labor-intensive part of the project.

Diy Wood Carving Wall Art Fh22apr 617 55 042

Step 7

Fasten the Cleats and Hang the DIY Wood Wall Art

Brush off the dust and wipe the surface with a damp microfiber cloth. When the wood is dry, apply your favorite finish.

To hang it, I marked a level line on the wall, located the studs and secured the wall cleat. Then I fastened the mating cleat on the back of the slab and displayed my new DIY wood wall art.

Diy Wood Carving Wall Art Fh22apr 617 55 049 Diy Wood Carving Wall Art Fh22apr 617 55 050