Save on Pinterest

How to Change a Bike Tire

Changing a bicycle tire is simple to master and to teach your kids!

How to change a bike tire how to change a tireFamily Handyman
Follow these simple steps for replacing a punctured bicycle tube. You can even fix the flat on the go if you have a spare tube, tire levers and a pump.

You might also like: TBD

How to Change a Bike Tire Step 1: Remove the tire and old tube

how to change a bike tube

Photo 1: Remove the tire

Pry under the bead of the tire with one of the tire levers and hook it to a spoke. Move over about 4 to 6 in. and insert the other tire lever. Pry it down and then slide it along the rim to release the tire.

The first step of how to change a bike tire is to release the brake and loosen the axle nut so you can remove the wheel from the bike. Most bikes have a quick-release mechanism on the brake and a quick-release lever on the axle. If youre not sure how to remove the wheels on your bike, check the manual or visit your local bike store and ask someone on staff to show you how. Do this before you have a flat so youll be prepared. For a guaranteed trouble-free fix, buy a new tube rather than patching the old one (see Valve Types below).

After removing the wheel from the bike, the next step is to take one edge, or bead, of the tire off the rim so you can remove the damaged tube (Photo 1). Pull out the tube. Then remove the tire completely from the rim, put it around your neck like a necklace and turn it inside out while running your fingers along the inside to feel for sharp objects. Be careful, thoughthere could be bits of glass lodged in the tire.

Tire Repair Kit

If you don’t want to walk home after having a flat, here’s a tip: Assemble a tire repair kit like this. You can put it in a resealable plastic bag and tuck it in a knapsack or buy a small pack that straps under your bicycle seat. Not including the seat pack, the kit cost us about $38.

Step 2: Install the new bike tube

how to change a bike tube

Photo 2: Install a new bike tire inner tube

Here’s how to replace a bike tube, partially inflate the new or patched tube and insert the valve stem into the hole in the rim. Then work the tube into the tire.

how to change a bike tube

Photo 3: Reinstall the bike tire

Press the bike tire back over the rim, being careful not to pinch the tube. If it’s too tight to push the last section by hand, use the tire levers to pry the bike tire onto the bike rim.

After checking the tire, put one bead back on the rim, leaving the other side loose so you can install the new (or patched) tube (Photo 2).

Photo 3 shows how to push the second tire bead back onto the rim after the tube is in place. When the tire is completely installed, check all around on both sides to make sure the tube isnt pinched between the tire and rim. To do this, push against the bead and look into the space between the tire and rim to be sure its clear.

Now youre ready to fully inflate the tire. But theres one last thing to watch for. Occasionally the bead may not seat properly on the rim, so stop before the tire is inflated to full pressure and rotate the wheel while you inspect the area where the tire and rim meet. If you see a spot where the bead isnt seated in the rim, let a little air out and work the bead into the rim with your fingers. Then inflate the tire to the pressure listed on the side. Reinstall the wheel and spin it to make sure its centered between the brakes and rotates freely. If youve done an emergency repair using the CO2 cartridge, you may not have enough pressure. When you get home or to a bike store or gas station, fill the tire.

Valve Types

When you go to buy a new tube, take the old tube with you and match the valve. Presta valves have a nut on a threaded shaft that seals the air in and must be loosened to inflate the tube. You need a pump thats compatible with a Presta valve to inflate these tubes. If you have Presta valves on your bike, keep a Presta-to-Schrader adapter with you so you can use a gas-station air pump to inflate your tire.

Required Tools for this How to Change a Bike Tire Project

You’ll need two tire levers and a pump or other inflating system.

Required Materials for this How to Change a Bike Tire Project

Avoid last-minute shopping trips by having all your materials ready ahead of time. Here’s a list.

  • New inner tube