Change the coolant yourself and save money on car maintenance. Our experts show how to change coolant in both newer and older (pre-2000) cars.
By the DIY experts of The Family Handyman Magazine
You might also like: TBD
How to Change Coolant Overview
In the old days (generally before 2000), changing your vehicles coolant was simple. That procedure is shown in Step 2, below. After 2000, cars got more complex and many DIYers got intimidated by the precise filling and air-bleeding procedures required to eliminate engine air pockets. But dont worry, its easier than it looks. All it takes to get back in the game is a one-time $83 investment in an air-powered refilling tool. The details follow in Step 3.
Either way, you can change your coolant yourself in about an hour. But before you do anything, check your owners manual for the recommended procedures and coolant for your car.
Draining and refilling coolant in older cars
Photo 1: How to drain a radiator: Open drain cock
Open the drain cock by unscrewing, twisting a quarter turn, or twisting and pulling. (The various styles are shown in the next photo.)
Drain cocks come in several different styles.
Photo 2: Remove the hose
Push together the clamp spring with a slip-joint pliers and slip the clamp away from the neck. Pull the hose free and drain the remaining coolant. If access is difficult, a hose clamp pliers saves time and bruised knuckles.
Hose clamp pliers
Hose clamp pliers are available at auto parts stores or online.
Photo 3: Add coolant
Stir 1 gallon of full-strength (not premixed) coolant and 1 gallon of distilled water together in a clean bucket before adding the mix to the radiator.
If you’re way past due for a coolant change and your cooling system is corroded, you should take your car in for a professional flush. The same is true if you’ve mixed different types of coolant in your radiator. But if you’re on schedule for a coolant change and your coolant is free of brown, gunky corrosion (extract a little coolant with a baster to examine it), you can skip the flush procedure and perform a simple drain and refill operation yourself and save money. Here’s how:
Start by buying the type of coolant listed in your owner’s manual. If your manual calls for an extended life coolant that isn’t available at the auto parts store, buy it from the dealer. Don’t buy a universal coolant. Using the wrong coolant can cause premature component failure and void your warranty.
Raise and safely support the front end of your car on jack stands. Place a large drain pan under the radiator and remove the radiator cap. If your radiator doesn’t have a cap, remove the pressure cap from the coolant tank. Then open the drain cock and drain the radiator.
Drain cocks come in several different stylesscrew threads, quarter-turn twist, and quarter turn and pull. Plastic drain cocks become brittle with age and can break easily, especially if you try to unscrew a quarter-turn twist style. So, buy a replacement drain cock at the auto parts store before you begin the job (they only cost a few dollars; return it if you don’t need it).
Then remove the lower radiator hose clamp and hose from the engine to drain the rest of the coolant. Use a slip-joint pliers to remove spring-style clamps. If you have trouble accessing or releasing the clamps with a pliers, buy a hose clamp pliers (see photo). Reconnect and clamp the radiator hose and reinstall the drain cock after draining.
How to Put Coolant in a Car
Follow the coolant manufacturer’s directions for diluting concentrated coolant. Mix the coolant and water thoroughly in a clean bucket. To prevent mineral deposits on internal engine and radiator surfaces, always use distilled waternever tap water. Leave the car raised while you refill the radiator to reduce the possibility of air pockets forming in the engine.
Slowly fill the radiator or coolant tank with fresh coolant until the coolant is 1 in. below the neck of the radiator or a few inches below the full mark on the coolant tank. Start the engine and let it run. After the engine warms, you’ll see the coolant level quickly drop in the radiator/coolant tank. That means the thermostat has opened and it’s time to add more coolant to bring the level to the top of the radiator, or to the HOT mark on the coolant tank. Check your owner’s manual or service manual to see if your car requires a special air bleeding procedure. Check for leaks, shut off the engine, install the cap, lower the car and go for a spin.
Used coolant is toxic waste. Pour it into a screw-cap plastic container and drop it off at a recycling center. Sweet-tasting coolant is irresistible to petsand poisonous. Just a small amount can be deadly. So soak up any spills with paper towels or rags immediately if you have pets wandering around.
Draining and refilling coolant in newer cars
Photo 1: Remove the lower hose
Slip the pointed end of the removal tool all the way into the end of the hose. Then pull it around the radiator neck to break the hose loose. Pull it off quickly and immediately direct the coolant into the drain pan.
Photo 2: Vacuum-fill the cooling system
Jam the fill tube into the coolant bottle. Then open the valve and let the vacuum suck fresh coolant into the system. Repeat the procedure until the system is full.
Changing your coolant yourself, including buying the air-powered refill tool, will save about $50 on your very first coolant change, and about $100 on each one after that. This procedure works for any cooling system thats not contaminated with rust or oil. Well show you how to check yours and then how to change the coolant.
Heres what you need to change coolant:
New coolant (2 gallons)
Air-powered refill tool (about $85)
Hose removal tool (about $4 from auto parts store or online)
Shop manual to locate block drain plugs
Absorbent paper towels
Wrenches and screwdrivers
Start by checking the condition of your coolant when the engine is cool. Remove the radiator or coolant reservoir cap and examine the coolant color. If it looks rusty (dont confuse orange coolant with rust), has crud or oil floating on the top, or looks like chocolate milk, call it quits and take it to a pro. You have problems that this procedure wont solve.
If the coolant looks clean, start the job by jacking up the vehicle and supporting it with jack stands. Next, place a large drain pan under the radiator. Loosen the lower radiator hose clamp with pliers (springtype clamp) or screwdriver (worm-drive clamp) and remove the hose (Photo 1). If the hose wont budge, use a hose removal tool (one choice is Tool Aid No. SGT13860 available through our affiliation with amazon.com) to break it loose (Photo 1). Let the radiator and water pump drain completely. Then reattach the lower radiator hose and clamp.
Next, locate and remove the block drain plugs (theyre in a different spot on every engine, so refer to a repair manual for the location of yours). Reinstall the block drain plugs and move on to the refilling step.
Refilling car with fresh coolant:
Insert the air tool (we used the UVIEW 550500 AirLift II Economy Cooling System Refiller; available through our affiliation with amazon.com) into the radiator neck or overflow bottle. Connect the exhaust hose and compressed air line and route the open end of the tools exhaust hose into an empty gallon jug or pail. Then open the valve and let the vacuum rise until the needle reaches the edge of the red zone on the gauge. Then fill with coolant (Photo 2). The vacuum sucks out any air pockets as it refills the system. When its full, just reinstall the radiator or overflow tank caps, remove the jack stands, and go for a spin.
Buying the Right Coolant
Most DIYers buy coolant at the auto parts store because the label says its universal, meaning it works in all cars. The carmakers disagree. Over the past several years, theyve issued service bulletins warning that universal coolants are often incompatible with the newer metal alloys and gaskets and seals used in their vehicles. The carmakers arent saying that just to increase sales of their proprietary coolants. Theyre seeing real (and expensive) damage caused by these coolants.
If you use the wrong coolant, you wont see the damage for a few years. But when you do, itll cost you a bundle. So heed the manufacturers warnings and buy coolant right from the dealer. Itll cost about $6 more per gallon (most vehicles only need 2 gallons), but the peace of mind is worth it.
Replace the thermostat and radiator cap when you change the coolant
The thermostat is the single most important component in your vehicles cooling system because it regulates engine temperature. Yet most owners dont replace it when they change their coolant. Thats a mistake: A failed thermostat is the second most common cause of engine overheating and engine failure (a failed radiator fan is No. 1). And a worn radiator cap (sometimes its on the overflow tank) can also contribute to engine overheating. Both parts are inexpensive (about $12 each at any auto parts store) and are cheap insurance against overheating.
A radiator cap is a snap to change (see photo). Its just a matter of unscrewing it and replacing it with a new one. Changing a thermostat yourself takes less than an hour (unless its buried). To find out how to replace yours, see How to Replace a Thermostat. But if yours is inaccessible, pay a shop to replace it.
Required Tools for this How to Add Coolant Project
Have the necessary tools for this DIY project lined up before you startyoull save time and frustration.
Slip joint pliers
You’ll also need a trouble light, jack stands, a drain pan, a bucket, a funnel, disposable gloves and hose clamp pliers. For newer cars, you’ll need an air-powered refill tool
Required Materials for this How to Add Coolant Project
Avoid last-minute shopping trips by having all your materials ready ahead of time. Here’s a list.