Learn how to make attractive stepping stones following a simple do-it-yourself method shown by our mosaic stone expert. Made from mortar and river rock, they’re tough and durable, yet easy and inexpensive to assemble.
By the DIY experts of The Family Handyman Magazine
You might also like: TBD
A full day
Overview: Creative pebble stepping stones
Finished stepping stone
Making DIY stepping stones begins with setting attractive stones in a bed of dry mortar.
Alice Medley loves to create works of art from the pebbles she collects. And she was generous enough to invite us into her garage workshop to show us how to make these beautiful pebble mosaic stepping-stones. She uses a “dry-set” technique that makes it easy to change or adjust the pattern as you go without having to dig the stones out of wet mortar. Get some ideas on how to building a stone path from these tips.
In addition to showing you how to make these DIY stepping-stones, we’ve included plans for an ingenious reusable wooden mold that Alice purchased from a North Woods carpenter. The initial investment for this project—about $50—gets you the plywood, a bag of mortar, pigment and muriatic acid. It’s enough material to make about seven or eight DIY stepping-stones. After that, each one will cost you less than a dollar.
Meet the Expert: Alice Medley
Alice started out using more traditional mosaic materials like tile and glass for her outdoor art projects. Then she discovered she could marry her love of stones with her love of mosaics. Alice learned this dry-mortar technique from Laura Stone, a stone mosaic artist from Minnesota. Alice has also created 4-ft.-diameter, built-in-place pad for her backyard fire kettle using the same technique and is waiting to see how it holds up through harsh Minnesota winters.
Step 1: Start by collecting the stones
Some of Alice’s vast collection of rocks.
Alice collects her stones on the north shore of Lake Superior. You’ll find similar stones in most parts of the country. Look for them in river and creek beds or along lakeshores. Wherever you find them, make sure you have permission and that it’s legal to collect them. Another possible source is your local landscape supplier or wherever landscaping stone is sold.
Alice likes to sort them by color. She’s got buckets and cans full of red, gray, white, brown and speckled stones. Keeping them sorted makes it a lot easier for her to find the right one as she creates a pattern.
Step 2: Build the stepping stone mold
Photo 1: Assemble the cement stepping stones mold
This plywood mold goes together quickly and comes apart easily after the mortar hardens. And you can use these cement stepping stones molds again and again.
A small sheet of 3/4-in. plywood and some 1-1/4-in. screws are all you’ll need to build the mold. Cut out the pieces according to the Cutting List. Figure A shows how the parts go together. When you’re done, brush linseed or vegetable oil on the mold to protect it from moisture.
Figure A: Stepping-Stone Mold
This mold designed for 12-in. x 12-in. stepping stones is made from 3/4-in. plywood.
You can download Figure A and enlarge it in “Additional Information” below. Also find a complete Cutting List in “Additional Information” below.
Step 3: How to make the stepping stone
Photo 2: Spread dry mortar in the form
Fill the plastic-lined form to about 3/4 in. from the top edge with dry Type S mortar. Level it with your gloved hand. It doesn’t have to be perfectly flat.
Photo 3: Arrange stones in a pattern
The only rule is to keep the stones close together so they touch and stand up and are not laid flat.
Photo 4: Tamp the stones level to the tops
Lay a board across the stones and pound on it with a rubber mallet to embed the stones in the dry mortar and set the tops level with each other.
Photos 2 – 4 show the assembly steps. Alice likes to add a little brown pigment to the dry Type S mortar mix to give the DIY stepping- stones a mellower look. You’ll find cement pigments and Type S mortar at home centers and masonry suppliers. Or you can cheat like Alice does and just mix in a little colored ceramic tile grout. Make sure to wear rubber gloves to protect your skin from the mortar, which can cause skin burns.
You don’t have to plan your pattern ahead of time. Alice says she has a design in mind and just starts arranging the stones. It’s easier to start along the edges or in a corner and work toward the center, though. You’ll have less fitting to do as you fill in the last few stones. Keep the stones close together and oriented with the long axis up and down. While it’s tempting, Alice cautions against laying a stone flat. She says it doesn’t look as good as you think it will and is more likely to pop out later. When you’re done tamping the stones into the dry mortar, inspect the space between the stones to see if there are spots that require more mortar. They should be buried at least halfway. Fill sparse areas with more mortar. Dust any dry mortar off the stones with a small brush.
Step 4: Wet the mortar
Photo 5: Sprinkle the stone
Adjust your spray wand or sprayer to the finest spray setting and sprinkle water over the completed stepping-stone to wet the mortar.
Photo 6: Tap on the form
Tap on the form with the mallet to remove air and help the water penetrate. Continue sprinkling and tapping until is seems like no more water will be absorbed by the mortar.
The trickiest part of the process is wetting the mortar (photo 5). We can’t tell you exactly how much water to add, but it’s better to sprinkle on several small doses than to get impatient and risk adding too much. Alice says the key is to alternate between wetting the top and tapping on the mold with the rubber mallet until it seems like not all of the water is being absorbed and bubbles quit appearing (photo 6). Expect to spend about 45 minutes sprinkling and tapping. When the mortar is thoroughly dampened, set the completed stepping-stone in a shady spot and cover it with a damp cloth and plastic. Wait at least 48 hours before removing the mold.
Step 5: Remove the mold
Photo 7: Pull off the mold
Allow the stepping-stone to harden and cure for at least two days. Then carefully flip it over and remove the mold. Clean it with water and then acid if needed.
After you remove the mold from the stepping-stone (photo 7), brush the stone off to remove any loose mortar and rinse it with clear water. If, after drying, the embedded stones have a film of mortar on them, clean it off with muriatic acid diluted according to the instructions on the container. Remember, always add acid to water, not the other way around, and wear rubber gloves and safety glasses.