Save on Pinterest

How to Sand Wood Faster

Speed up your woodworking projects with these sanding tips

man uses two orbital sanders at onceFamily Handyman
Sanding wood can get boring, but you can finish this tedious chore in as much as half the time—and with better results—if you know a few tricks.

You might also like: TBD

Grab a second sander

Double your productivity

With two sanders, you can put both hands to work and, well, sand twice as fast-duh! Keep the sanders close together and think of them as a single machine. If your hands wander apart into separate territories, you’ll oversand some spots and miss others.

Skip a grit

You dont have to use every single grit as you sand your way from coarse to fine. Instead, use every other grit; 80-120-180 or 100-150-220, for example.

Video: Make Your Own Woodworking Sanding Blocks

Sand faster with suction

Keep the surface clean

Connecting to a vacuum doesnt just cut down on dust. It actually allows your random orbit sander to work faster. Even with the sanders built-in dust collection system, the sander rides on a thin cushion of dust that prevents full contact between the grit and the wood. So, by increasing dust removal, a vacuum improves sander efficiency. On some sanders, hooking up to a vacuum doubles the sanding speed. Check out how to set up a shop vacuum for dust collection.

Stop the swirls

Slow and steady wins the race

For faster hand sanding, you just press harder and move faster. But with a random orbit sander, that strategy will actually slow you down. Too much pressure or speed creates tiny swirling scratches that youll have to sand out sooner or later (often later, after stain makes them visible). A light touch and patience are the key to avoiding those swirls. Just rest your hand on the sander; dont press. The weight of your arm provides enough pressure. Move at a snails pace; no more than 1 in. per second. Going that slow feels unnatural and takes some self-discipline. So try this: stretch out a tape measure along your project and watch the second hand on a clock while you sand. After about 30 seconds (or 30 in.), youll get used to the right speed.

Know when to stop

How smooth is smooth enough? We put that question to professional woodworkersand couldnt get a straight answer. (Woodworkers are notoriously noncommittal.) It depends… was the typical response. Heres what that means:

Open-grain woods like oak and walnut have coarse grain lines and a rough texture. So sanding to very fine grits is a waste of time. Closed-grain woods like maple and cherry have a smoother, more uniform texture. So they need to be sanded with higher grits before the sanding scratches will disappear.

The finish matters too. For thick coatings like polyurethane, varnish or lacquer, most of the guys we talked to stop at 150 grit on open grain woods, 180 on closed. For oil finishes, which dont create much buildup, higher is better; 220 on open grain, 240 on closed.

Video: How to Sand Wood By Hand

Bigger is better*

Five-inch sander

Five-inch sanders are inexpensive and easy to control.

Six-inch sander

Six-inch sanders cost more but sand almost half again as much surface.

A 5-in. random orbit sander is the essential sanding tool for any DIYer. If youre a serious woodworker, youll also love a 6-in. version. An extra inch may not seem like it would produce a big jump in sanding speed, but it means almost 45 percent more sandpaper surface, plus a more powerful motor. Sanding faster comes at a price, of course: Six-inch sanders are two to three times more expensive than five-inchers, and the larger sanders are a little harder to control, especially on vertical or narrow parts.

*Sometimes

Presand your stock

Before cutting up boards for your next project, sand them all with 80- or 100-grit. You might waste a little time sanding areas that will end up as scraps, but youll come out ahead in the long run. The initial sandingremoving scratches, dents and milling marksis the heaviest sanding. And if you sand boards before cutting or assembly, you can use the tool that does deep sanding fastest: a belt sander. Sanding whole boards also eliminates the repetition of stopping, starting and setup for individual parts.

Save your sanity

Music makes the job easier

Sanding Syndrome is a psychological disorder caused by fussy attention to detail combined with brain-rotting boredom. Symptoms include drooling on the project, hearing voices in the whine of a belt sander and seeing cartoon characters in wood grain patterns. Theres no sure way to prevent Sanding Syndrome, but a little entertainment helps. Earmuffs or earplugs with built-in speakers block out power-tool noise while reducing boredom. Search online for stereo earmuffs or noise isolating earbuds to browse a huge selection. Prices range from $25 to $200.

Stack ’em and sand ’em

Save time by gang sanding

Gang sanding with a random orbit or belt sander lets you smooth a bunch of edges in one pass. As a bonus, the wider surface prevents the sander from grinding too deep in one spot or tilting and rounding over the edges. This trick also makes sanding a self-correcting process; all the parts will end up exactly the same.

How to use a sander: Sand across the grain

Smooth large areas fast

The first commandment of sanding: Sand with the grain. But when you have a lot of wood to grind off, break that rule and run your belt sander diagonally across the grain (at about 45 degrees). Instead of scratching away at the wood fibers, the belt will rip them out. Its incredibly fastand dangerous. Be careful not to gouge too deep, and expect to follow up with some heavy sanding to smooth the plow marks left behind.

Premium paper works faster

Use the best

Better sandpaper has sharper particles of grit, which bite into wood faster. And not just a little fastera lot faster. Premium paper removes wood at two or three times the rate of standard paper. It costs a bit more, but the grit stays sharp much longer, so you actually save money, whether youre using sheets, discs or belts. Norton 3X, 3M SandBlaster and Gator Ultra Power are three common lines.

Prevent glue spots

Masking tape saves the day

Glue spots are cruel. When you think all the tedious sanding is done and you apply stain or even varnish, theyll appear like bleached smudges. Getting rid of them means more sanding. On a flat surface, glue drips arent a big deal. Youll remove them automatically as you run through the normal sanding process. But in hard-to-sand spots like inside corners, prevention is the best strategy, and a little masking tape will save you a lot of hassle.

Required Tools for this Project

Have the necessary tools for this DIY project lined up before you startyoull save time and frustration.

  • Belt sander
  • Clamps
  • Dust mask
  • Hearing protection
  • Orbital sander
  • Rags
  • Safety glasses
  • Sanding block
  • Shop vacuum
You may also want stereo headphones.

Required Materials for this Project

Avoid last-minute shopping trips by having all your materials ready ahead of time. Here’s a list.

  • Masking tape
  • Sandpaper