How To Clean or Change an Air Filter in a Riding Lawn Mower

Want to keep your riding lawn mower working well all the time? Knowing when to clean or replace a lawn mower air filter matters. Here's how to do it.

Next Project
Time

An hour or less

Complexity

Beginner

Cost

Less than $20

Introduction

Want to keep your riding lawn mower working well all the time? Knowing when to clean or replace a lawn mower air filter matters. Here's how to do it.

Tools Required

  • Bucket
  • Portable air compressor with hose and air spray nozzle

Materials Required

  • Clean shop rags
  • Replacement air filter to fit your mower
  • Warm soapy water

Project step-by-step (7)

Step 1

Disconnect spark plug wire

  • Examine the engine until you find the spark plug, then disconnect the wire connected to it. This ensures the engine won't accidentally start while you're working.

1 Spark Plug Wire

Step 2

Open filter housing and remove air filter

  • Examine the engine, looking for a removable plastic cover on the top or possibly on either side. This is the air filter housing.
  • Remove the air filter housing cover. Most riding lawn mower models are designed for this to be done by hand.
  • If your filter housing is held in place with bolts, unthread and carefully place them somewhere nearby where they won't get lost or fall into the engine.
  • With the cover off, gently pull the air filter out from its housing and put it to one side. Depending on the model of mower you're working on, the filter might be a paper cartridge style or a simple piece of foam. Cleaning procedures will vary slightly for each.

2 Remove Filter Housing

Step 3

Protect the air inlet

  • With the air filter free of its housing, stuff a clean, dry shop rag into the inlet port at the back of the housing. This prevents debris from getting into your carburetor during cleaning.
  • Be sure to leave enough of the shop rag sticking out of the port that you'll easily be able to pull it out when you're done.

3 Protect Air Inlet

Step 4

Clean the filter housing

  • Use your air compressor and spray nozzle to blast any dirt and debris from the inside of the filter housing. Be sure the shop rag is firmly blocking the inlet port before doing this.

4 Clean Filter Housing

Step 5

Determine if the filter needs cleaning or replacement

  • Examine your air filter. If it's the paper cartridge type, look closely at the paper pleats. If they're only moderately dirty, chances are cleaning the filter will be sufficient. If they're completely caked in dirt and discolored, you'll need to replace the filter.
  • If your filter is the all-foam variety, it can be cleaned in warm, soapy water if it's not too dirty. As with the paper cartridge filter, replace your foam filter if it's completely caked in dirt and debris that won't come off easily.

5 Examine Filter

Step 6

Install new filter or clean old one

  • If your air filter is beyond saving, throw it out and install a new one of the same type. Check your mower's manual or do a Google search to find filters compatible with your machine.
  • Be sure to remove the shop rag you stuffed in the air inlet before installing the new filter.
  • If your filter still looks like it has some life left, tap it gently against the nearest hard surface to knock loose as much dirt as you can. If it's a foam filter, gently wash it in warm, soapy water, then set it somewhere warm to dry.
  • If you've got a paper filter, stuff a clean shop rag into the center to keep dirt out, then blow off the outside with the air compressor, getting all surfaces as clean as possible.
  • With the outside of your paper filter clean, remove the shop rag, then insert your air spray nozzle inside and blow out the filter from the inside out.
  • If your paper cartridge filter has a removable outer wire mesh or foam sleeve, take it off and clean it separately. If you use water, be sure to let the protective cover dry fully before replacing it over the filter.

6 Clean Filter

Step 7

Re-install cleaned filter

  • With your filter fully cleaned, remove the shop rag from the air inlet, then carefully re-install the filter.
  • Replace the filter housing cover, then reconnect the spark plug wire and you're done!

7 Reinstall Filter